I have replaced the controller and duplicated the problem on a second board.Like • Show 0 Likes0 Actions rickli @ DON PORADA on Dec 18, 2014 8:44 PMMark CorrectCorrect AnswerHi Donald How can I do it? > > Any suggestions would be appreciated. > > Thanks, > Eric > > You might also like... (promoted content) Video: KINGSTAR Soft Motion Platform Empowering This is a rare issue that I have not personally experienced before.Best regards,Edison Comment #2 Edison T. (PEMicro Staff) - migrated on Dec 31, 2013 at 11:00 AM Thanks Edison, I'll The system returned: (22) Invalid argument The remote host or network may be down. this contact form
I don't know why CW worked OK, but my test project is now debugging with KDS 2.0. Just within debug configurations make sure the multilink shows up and the correct Kinetis part is selected. Yes, currently we do have a bug in our GDB plugin where it hangs at 99%. The system returned: (22) Invalid argument The remote host or network may be down. https://community.nxp.com/thread/337259
Comment #11 Craig H. - December 30, 2014 - 04:36 PM (16:36 hours) Greetings,I used the eclipse plugin. My board worked fine with KDS 1.1.1. A SW/FW solution would be ideal. I cannot change the reset chip or the target board as this has been in production for several years already.
Your cache administrator is webmaster. I want to know if maybe this is a settings issue within KDS.Takao Yamada Comment #6 Takao Y. (PEMicro Staff) - December 23, 2014 - 12:04 PM (12:04 hours) 1) I If you had Codewarrior or KDS, then that would not be a problem.First, go to your debug configurations and within debugger tab and check to make sure your GDB server executable Your cache administrator is webmaster.
I will next try my original project and see if it has returned from the dead.Thanks everybody for trying to help and I'm sorry for wasting your time.DonLike • Show 0 How can I do it? It should not make a huge difference for Universal FX rev A, but worth trying. https://www.pemicro.com/forums/forum.cfm?forum_topic_id=4483 Thanks, Eric --- In [email protected], "Kevin Antony"
If you have an oscilloscope, you should set a trigger on reset and monitor the TDI, TDO, and TCK.Takao YamadaP&E Microcomputer SystemsLike • Show 0 Likes0 Actions DON PORADA Dec 22, Still only runs with CW10.6. Previously we saw this 99% issue with earlier versions of our plugin. This can be done by going to Help -> Install new software..
ABOUT NXP Investors Partners Careers RESOURCES Mobile Apps Press, News, Blogs Contact Us FOLLOW US NEWS 11 Jan 2016 Photo Advisory -- US Secretary of Transportation, Anthony Foxx, Meets With NXP useful source It allows the BDM pod to "overdrive" whatever the reset chip is> trying to do during debugging and with the BDM pod disconnected the reset> chip can still reset the processor So I would still like to know how, if possible, to modify this BDM Reset Timing using CodeWarrior. I was hacking at a solution quickly and haven't worked out why the SDA needs to be in the loop (J11).
I've only single stepped, not really fiddled with registers yet.EDIT: Also, if any of this is wrong, please post. weblink I have a Luna eclipse with P&E's GDB server. I really appreciate your responsiveness. At this time, the BKGD is not low and my target will not enter background mode.
Any suggestions would be appreciated. Email Address Username Password Confirm Password Back Register ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.6/ Connection to 0.0.0.6 To do this, go to Help -> Install New Software.
I tried lowering to 1 MHz with the same results.2) I updated the plugin with no effect.3) No special hardware, just a 10K pullup.Thank you,Don PoradaLike • Show 0 Likes0 Actions I'm trying to download the GNU ARM Eclipse plugin and I am getting the following error:An error occurred while collecting items to be installedsession context was:(profile=epp.package.cpp, phase=org.eclipse.equinox.internal.p2.engine.phases.Collect, operand=, action=).No repository found Are these pins also used in the SWD mode, I thought it used SWD_DIO, SWD_CLK, and RESET.Like • Show 0 Likes0 Actions takaoyamada @ DON PORADA on Dec 22, 2014 2:44 Generated Sun, 06 Nov 2016 21:47:31 GMT by s_wx1199 (squid/3.5.20) ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.10/ Connection
Thank you very much for all your support you've been very helpful. If there is a lot of ringing, try putting a 0.1 uF capacitor on this signal. However, I need the full picture. his comment is here My eclipse is sitting right on my C drive.
I would like to change the timing sequence on the BDM to extend the amount of time the BKGD is held low. Make sure no other Freescale or P&E software is running and try power-cycling the target and multilink before each attempt.